Metlab Corporation, Metallographic, Metallurgical, Metallography, Equipment abrasive, metallographic, cutting, machine, sectioning phenolic, metallographic, mounting, machine, mounting, hot mounting metallographic, grinding, machine, grinding polishing metallographic, polishing, machine, polishing grinding Table-top Surface grinder, spectroscopic, sampl,e preparation, of steels and irons petrographic sample preparation, Preparing thin sections, thin sectioning, metallographic
Metlab Corporation, Sectioning, Metallographic, Metallurgical, Metallography, Equipment Metlab Corporation, Hot Mounting, Metallographic, Metallurgical, Metallography, Equipment Metlab Corporation, Grinding, Metallographic, Metallurgical, Metallography, Equipment Metlab Corporation, Polishing, Metallographic, Metallurgical, Metallography, Equipment Metlab Corporation, Spectroscopy, Metallographic, Metallurgical, Metallography, Equipment Metlab Corporation, Petrography, Metallographic, Metallurgical, Metallography, Equipment


SAMPLE PREPARATION FOR METALLOGRAPHIC, METALLOGRAPHY, METALLURGICAL MACHINE

Sectioning Mounting Grinding Polishing Spectroscopy Petrography

After cutting the specimen, the next step is mounting. The aim of mounting is to handle small or odd shaped specimens and to protect fragile materials, thin layers or coating during preparation as well as to provide good edge retention. Mounting produces specimens with uniform size so that it is easier to handle in automatic holders for further preparation steps.

Basically, two methods are available: Hot Mounting, Cold Mounting
In hot mounting, the specimen is mounted under heat and pressure with a hot mounting press.
Cold mounting is preferred for samples which are sensitive to damage from heat and pressure (like coatings, PCB, etc.) Cold mounting resins are easy to use and require mixing which is then poured into a mould and allowed to set.
METPRESS A, hot mounting press 


METPRESS A
-Fully automatic
-Electro Hydraulic Pressure (no airline required)
-LCD HMI display with user friendly touch screen controls
-Pressure up to 350 Bars (5000 psi)
-Temperature up to 200 C
-Mould Size 1,1,1,2,25mm,30mm,40mm,50mm
-Intermediate ram included for dual mounts
-Robust bayonet closer
-Heating power of 1000 watts
-Corrosion resistant steel construction
-Cycle completion alarm notification

 
METPRESS A
Hot Mounting Press
 
QUOTE REQUEST BROCHURE 
     
     
ECOPRESS 50, hot mounting press 


ECOPRESS 50
With one cylinder is a cost effective digital press with hydraulic pressure (requires no air), pressure upto 300bar, temperature upto 200c, heating power of 1250W, mold sizes from 25-500mm. 220V, 1 phase, 50/60 Hz

 
ECOPRESS 50
Hot Mounting Press
 
QUOTE REQUEST BROCHURE 
     

ECOPRESS 100, hot mounting press


ECOPRESS 100
Programmable Automatic Mounting Press with one cylinder, 5,7" HMI touch
screen control, program based mounting sequences, electro hydraulic pressure (requires no air), pressure upto 300 bar, temperature upto 200 C, operation time upto 59:99 minutes, short cycle time, thermostatically controlled heating power of 1250W, automatic cooling cycle with two modes of cooling rates (fast cooling and slow cooling), programmable preheating and preloading,selectable mould sizes from 25mm to 50mm, audible warning signal. 220 V, 1-phase, 50/60 Hz.

ECOPRESS 100
Hot Mounting Press
QUOTE REQUEST BROCHURE
     

ECOPRESS 200, hot mounting press


ECOPRESS 200
Programmable Automatic Mounting Press with two cylinders, 5.7" HMI touch
screen control, program based mounting sequences, electro hydraulic pressure (requires no air), pressure upto 300 bar, temperature upto 200 C, operation time upto 59:99 minutes, short cycle time, thermostatically controlled heating power of 2X1250W, automatic cooling cycle with two modes of cooling rates (fast cooling and slow cooling), programmable preheating and preloading, selectable mould sizes from 25mm to 50mm, audible warning signal, ready for  operation. 220 V, 1-phase, 50/60 Hz.

ECOPRESS 200
Hot Mounting Press
QUOTE REQUEST BROCHURE 
     
vacumet, cold mounting press


VACUMET
Self-contained vacuum impregnation unit, with built-in pneumatic vacuum
system of -0.65 bar, vacuum gage.
110v, 1 phase, 50/60 Hz.

VACUMET
Cold Mounting Press
QUOTE REQUEST BROCHURE 
     
     
     
Sectioning Mounting Grinding Polishing Spectroscopy Petrography
    4011 Hyde Park Blvd  -  P.O. Box 1075  -  Niagara Falls, NY 14302  - 1-800-828-6866